China 6 Pot Brake Kit manufacturer

410x36mm Auto Brake Discs Center Bell For Audi RS6 C7

Product Details:
Place of Origin: china
Brand Name: Jekit
Model Number: 410*36
Payment & Shipping Terms:
Minimum Order Quantity: 1 set
Price: Factory direct price
Packaging Details: 40*40*20cm
Delivery Time: 5-8 work days
Payment Terms: T/T, Western Union,paypal
Supply Ability: 99set

Detail Information

Product Name: Auto Brake Discs Bell Color: Balck
Rotor Size: 410*36mm Center Bell Material: Aluminum
Rotor Material: Iron Fit Wheel: 22 Inch
Application: Brake Caliper Type: Brembo Floating
High Light:

410x36mm Auto Brake Discs


RS6 Auto Brake Discs


Audi C7 Auto Brake Discs

Product Description

Jekit RS6 C7 410x36mm Auto Brake Disc Center Bell For Audi RS6 C7


We Jekit factory can offer different disc size: 285x24/295x24/300x24/300x28/330x24/330x28/330x32/350x34/355x28/355x32/360x28/362x32/360x36/370x36/370x34/380x28/380x32/380x34/380x36/390x36/400x28/400x36/405x34/410x36/420x40mm

you can choose the modified brake disc according your car request

We can make alloy disc center cap for different car model. Such as Benz/BMW/Audi/Porsche/VW etc


Installation steps of modified brake
Step 1: clean the bearing. After removing the original brake system, clean the bearing part with a steel brush, remove the rust on it, and measure whether the bearing plane is deformed to ensure that the upgraded brake disc fits closely on the bearing.


Step 2: apply sound insulation adhesive to the bearing. Thin application of sound insulation glue on the bearing plane of the original factory can not only prevent the bearing from rusting, but also make the contact between the bearing and the brake disc closer


Step 3: fix the brake disc. Place the brake disc on the bearing, but pay attention that the screws in this part don't have to be tightened in a hurry. At this step, just fix it.


Step 4: install the axle code and caliper. After the brake disc is fixed, fix the bridge code on the sheep horn, and then fix the caliper on the bridge code to ensure the correct installation position of the bridge code, the correct installation direction of the bridge code and the correct installation direction of the caliper. This step is the same. There is no need to tighten the screws in a hurry, just fix them in a fixed position.


Step 5: accurate measurement of caliper position. In fact, this step is often the most easily overlooked, but it is also the most important step in the whole installation process. In the future use of many modified calipers, the uneven strength of left and right calipers, inconsistent wear of brake pads, and even brake jitter are related to this step. This step is to use an accurate vernier caliper to measure whether the caliper and the brake disc are accurately symmetrical up, down, left and right. On the premise of ensuring accuracy, the force pushed out by the piston can be evenly dispersed on the back of the brake pad, completely avoiding the problem of uneven left and right force, resulting in the failure of the caliper to work completely.
If it is found that the upper, lower, left and right positions of the caliper cannot be accurately symmetrical and the error is great, then the installation must be abandoned and the supplier is required to re customize the caliper bridge code. Any installation method of modifying the bridge code or using gaskets is unacceptable to me.


Step 6: tighten the screws correctly. After confirming the position of the caliper, the fixed screws need to be coated with screw glue. According to the requirements of the caliper manufacturer, use the correct torque wrench to fix the caliper screws. This is very important. Do not use an air cannon.


Step 7: install the brake pad + fixed pressing plate. The brake pads of different calipers are installed in different ways, so this step can also be advanced before the calipers are fixed. The more important thing here is to apply sound insulation glue, which can not only make the brake pads work more smoothly, but also reduce the probability of abnormal noise of the brake pads as far as possible. After installing the brake pad, the spring pressing plate at the top should also be installed


Step 8: installation of steel throat oil pipe. For refitting brakes, the importance of steel throat need not be said. It should be noted here that the steel throat with appropriate length should be selected according to different models, and the steel throat with correct interface should be matched according to the model of caliper.


Step 9: exhaust air from brake oil. This part is very important for the braking system. If the braking system contains air, it will lead to insufficient braking force at light level and loss of braking by directly depressing the pedal at heavy level. Here, I personally suggest using the special equipment for brake oil replacement to directly replace all brake oil. If the brake oil is very new, use the brake oil of the same brand and model to drain the pedal and replenish the oil.


Step 10: check oil leakage + confirm interference. After the air exhaust operation of the brake oil, after a simple test run, stand for 30 minutes, and check whether there is oil leakage at the interface of the brake oil pipe. Once it is found, it must be handled immediately and the air exhaust operation must be carried out again. In addition, after lifting the car, turn the wheels left and right respectively, and observe whether there is any movement interference between brake calipers, bridge codes, screws, oil pipes and other parts, so as to ensure that there is no friction between these key parts and any parts of the body, and the oil pipes are not pulled. Only in this way can we ensure driving safety in the future.

The 10 steps of installing the modified brake system are absolutely the most comprehensive installation. When upgrading and modifying the brake system in the future, in addition to choosing a set of good brake system products, please also pay attention to the correct installation of the brake system. Any hidden danger may have an impact on the future, ranging from abnormal noise to driving safety.


Item Name  Auto Brake Discs
 Disc Size 410*36mm
 Center  type  Floating
 What data need to make center bell  Disc diameter/thickness/PCD/Locating edge/Depth
 one pair included

1 pair brake disc with 1 pair center cap a


410x36mm Auto Brake Discs Center Bell For Audi RS6 C7 0410x36mm Auto Brake Discs Center Bell For Audi RS6 C7 1410x36mm Auto Brake Discs Center Bell For Audi RS6 C7 2

Get in touch with us

Enter Your Message

You Might Be Into These